Part One: Spatial Strategy and Policies (Regulation 19)

Ended on the 29 November 2024

Managing Heat Risk

12.23. As part of the Plan's proactive approach towards mitigating and adapting to climate change, Policy DLP43 sets out the requirements for managing heat risk within new development proposals.

Policy DLP43 Managing Heat Risk

  1. Development proposals[47] should minimise both internal heat gain and the impacts of urban heat islands[48] by using appropriate design, layout, orientation and materials.
  2. Development proposals will be expected to demonstrate how their potential for overheating and reliance on artificial cooling systems will be reduced, in accordance with the following cooling hierarchy:
    1. minimise internal heat generation through energy-efficient design;
    2. reduce the amount of heat entering a building through orientation, shading, albedo[49], fenestration, insulation and the provision of green roofs and walls (see also Policy DLP39 Design Quality);
    3. manage heat within a building through exposed internal thermal mass[50] and high ceilings;
    4. provide passive ventilation;
    5. provide mechanical ventilation;
    6. provide active cooling systems[51].
Justification

12.24. Global temperatures are rising, and this has been paralleled by changes in the weather in the UK. The Met Office published a document[52] in 2022 outlining current trends and predictions in the UK, including the following:

12.25. The average temperature over the most recent decade (2009-2018) has been on average 0.3°C warmer than the 1981-2010 average and 0.9°C warmer than the 1961-1990 average. All the top ten warmest years for the UK, in the series from 1884, have occurred since 2002. (paragraph 2.1)

12.26. The urban heat island effect [53]is caused by extensive built-up areas absorbing and retaining heat during the day and night, leading to those areas being several degrees warmer than their surroundings. With higher temperatures across the country, the likelihood of heat being trapped in this way is very likely to increase.

12.27. Retained heat can become problematic, to the point where circumstances can lead to physical discomfort and disruption, but for those with certain health conditions, the very young or the elderly, the effects can be serious. The use of green roofs and / or walls can provide some mitigation by shading roof surfaces and through the mechanism of evapotranspiration.

12.28. The concept of thermal inequity[54] will also have relevance in areas of the borough, whereby because of uneven social geographies, urban heating effects impact disproportionately on poorer / marginalised communities living in urban environments. This is exacerbated by a planning policy approach that concentrates development in urban areas, at higher densities and in taller forms. The removal of urban greening and trees to facilitate increased development densities will have further adverse effects on ambient temperatures in the vicinity.

12.29. Certain aspects of building design intended to increase energy efficiency and reduce heat demand, such as increased glazing and airtightness, can also exacerbate heat risk and cause uncomfortable living conditions. Design solutions can be found in the hierarchy proposed in Policy DLP43.

12.30. Means of minimising heat risk may include, though not be limited to, inclusion of mitigation measures such as: -

  1. solar shading, for instance through landscaping or brise-soleil[55],
  2. using appropriate materials in areas exposed to direct sunlight,
  3. using landscaping and permeable surfaces to mitigate against flooding / run-off, counter poor air quality and allow for heat absorption.

12.31. Mechanical air conditioning will utilise more energy and generate significant amounts of additional greenhouse gases and thus should be avoided where possible.

12.32. As addressed in Policy DLP33, the use of trees in landscaping schemes can generate significant natural shading. The layout and orientation of new houses should also be considered carefully, to avoid existing or newly planted trees creating excessive shading during cooler, darker times of the year.

12.33. Canals and other water bodies can also be used as a potential component in managing heat risk. Bodies of water have a natural cooling effect through evaporation and help to provide resilience in the urban environment.

Evidence
Delivery
  • Development Management and Building Regulations processes.

[47] excluding domestic extensions

[48] Caused by extensive built-up areas absorbing and retaining heat

[49] The reflectivity of a surface. A high albedo surface reflects the sun's heat back into the atmosphere; low albedo surfaces absorb it. Pale-coloured surfaces have a high albedo and can help to minimise heat gain

[50] Thermal mass' is a material's capacity to absorb, store and release heat

[51] Systems using energy to provide cooling. They circulate a coolant (gas, fluid) to transfer heat from one place to another

[52] UK Climate Projections: Headline Findings August 2022

[54] The concept of thermal inequityshould be Jason Byrne et al 2016 Environ. Res. Lett. 11 095014

[55] Architectural feature that reduces heat gain within a building by deflecting sunlight

For instructions on how to use the system and make comments, please see our help guide.
back to top back to top